Home > Pinnacle Studio > Pinnacle Studio Capture Error

Pinnacle Studio Capture Error

Under Sound, Video and Game controllers, find the capture device and click on it to highlight it. If the capture device is Pinnacle/Dazzle hardware such as the 500 USB or 700 USB or Dazzle DVC 100, reinstall the drivers with the following steps Shut down Studio Go to If you have another network card in your system or you have installed the firewire card more than once, you might see this #2. The Camcorder Controller. http://iipseconline.com/pinnacle-studio/pinnacle-studio-9-capture-error.html

You must have the camcorder or VCR playing video before pressing the Start Capture button. 4. Use these to navigate through the tape to find the scenes you want to include in your project. If you are getting this error, please do the following: 1. See if capturing now works.

To capture from analog, select the correct device for Video and Audio. follow any on screen instructions to finish loading the driver if any appear. All Rights Reserved. Advertisement Recent Posts Software User Instructions tomsonn replied Oct 24, 2016 at 1:21 AM Computer runs extremely slow tomsonn replied Oct 24, 2016 at 1:08 AM Trying to boot from rescue

Does anyone have a clue what we can try next???? For a Pinnacle 500-USB, it will be listed as such. Check the DV, Digital 8 or HDV camcorder for ALL of the following: Ensure the camera is in PLAY mode. The time now is 05:28 AM.

If both the 1394 controller and DV camcorder drivers are listed properly in Device Manager and Studio will still not capture from the device, then try to capture using AmCapture. Studio's Capture Album does have the ability to display 16:9 and 4:3 footage at the proper aspect ratios, an option we'll explore in this chapter. Examples of digital devices are DV, Digital 8 or HDV camcorders. The ultimate fix is probably a fresh install or restore from a restore CD, but that requires a lot of planning and backup or you end up losing stuff.

Here's how it works: I chronicle family events with my DV camcorder continuously, usually taking two or three months to complete a 60-minute tape of holidays, school events, and other camera-worthy The purpose of the message is to alert customers that the video signal is not detected so capturing cannot proceed. 1. Note the lack of playback controls in the Player window. Neither USB nor Firewire connection. 1.What do you see in the device manager under "IEEE 1394 Bus host controllers"?

Turn the camcorder on and off. 3. http://forum.videohelp.com/threads/202614-Capture-error-in-Pinnacle-Studio-Plus-v9 If there is a yellow “!” to the left of the 1394 driver, you will need to reload the driver. This site is completely free -- paid for by advertisers and donations. I keep getting the error message: "Prepare Record Failed!!! #0" What do I need to do to get through this issue?

The same cable that carries the DV video to your computer lets you control the camera, so you can start, stop, rewind, and fast-forward your DV camera within Studio--a useful capability have a peek at these guys Start -> Control Panel -> System. If the hardware is installed successfully it should be listed under Sound, Video and Game controllers without any exclamation marks.   Was this article helpful? 0 out of 0 found this Also, Windows (XP and Vista) will typically give a "Found New Hardware" or messages when the camcorder is turned on as the device is detected.

Change it from DV source to Analog source. Articles Forum New Posts FAQ Community Member List Forum Actions Mark Forums Read Quick Links Today's Posts Blogs Register Advanced Search Forum Video Editing Forums Archive Pre January 2014 Video Editing Disconnect and reconnect the 1394 cable. 4. check over here In trying to connect a Sony Digital Handicam to the firewire port, the driver loads into device manager/imaging devices "bong" is heard and all appears fine for 3 sec to 1

This chapter is from the book  This chapter is from the book Pinnacle Studio 10 for Windows: Visual QuickStart Guide Learn More Buy This chapter is from the book This The Player. Figure 3.3 The Diskometer tells you how much video you can store on your capture drive, lets you choose among the three capture options, and contains the Start Capture button.

First, the wheel and associated text describe how much additional video you can store on the capture drive at the selected format and capture quality.

Thanks for clearing up. Open Windows Device Manager. The goal is to get video playing in the preview window before attempting to capture, otherwise you are likely to get the error. Note that the interface is different when you're capturing from a DV camcorder than it is when you're capturing from an analog camcorder. (See Chapter 4 for the scoop on analog

a. restart the computer. Make sure you are not using a USB cable connected to a USB port on a still image camera or a DV/DVD camcorder. this content In Capture mode, Studio has four main components: the Album, where Studio displays the captured clips; the Player, which displays video during capture; the Camcorder Controller; and the Diskometer.

Were you able to solve the problem at all?