Home > Ping Error > Ping Error

Ping Error

Contents

From Router1 you can ping Router2. Your cache administrator is webmaster. Ping Request Could Not Find Host... (none) If you see this error message, PING was unable to determine the IP address from the hostname provided. Note that if the routing table is correct, this simply forwards the packet to the loopback address of 127.0.0.1. http://iipseconline.com/ping-error/ping-error-65-xp.html

Try to ping the destination again. Sending 5, 100-byte ICMP Echos to 34.0.0.4, timeout is 2 seconds: ..... Jan 20 16:40:24.303: IP: s=20.0.0.1 (local), d=12.0.0.2 (Serial0), len 100, sending Jan 20 16:40:26.303: IP: s=20.0.0.1 (local), d=12.0.0.2 (Serial0), len 100, sending. share|improve this answer answered Jun 2 at 13:28 wmollenvanger 1 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up using Google Sign up http://www.onlinecomputertips.com/networking/ping.html

Ping Error Message General Failure

Top Of Page Destination Host Unreachable This message indicates one of two problems: either the local system has no route to the desired destination, or a remote router reports that it Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms Router1# Jan 20 15:54:47.487: IP: s=12.0.0.1 (local), d=12.0.0.2 (Serial0), len 100, sending Jan 20 15:54:47.491: ICMP type=8, code=0 !--- This See Configuring Address Resolution Methods for a detailed explanation. Delete the entries with arp -d < IP address >.

Windows 2000 Error Messages Reference Command Line Utilities PING PING Request timed out. ... Use the Route utility to check the local routing table. How to make your world’s revolutions feel realistic? Ping Response Codes Retrieved 20 December 2010. ^ "Shields Up, Firewall Test".

Success rate is 0 percent (0/5) This time, the source address is 20.0.0.1, and it is not working! Ping Messages Explained Q Source quench (destination too busy). Destination host unreachable. ... http://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/ios-software-releases-121-mainline/12778-ping-traceroute.html You can change this default using an extended ping: Router1#ping Protocol [ip]: Target IP address: 12.0.0.2 Repeat count [5]: Datagram size [100]: Timeout in seconds [2]: 30 Extended commands [n]: Sweep

Resolved Issue Concerned: I issued the above commands on same workstation a few weeks ago without issue. Ping Output interface Serial0 ip address 34.0.0.3 255.255.255.0 no fair-queue ! Should I tell potential employers I'm job searching because I'm engaged? It didn't happen for all sites, just sites that we (the company) published.

Ping Messages Explained

End with CNTL/Z. http://superuser.com/questions/433416/why-do-i-get-general-failure-when-pinging-host-name-on-a-win-7-node-on-the-net It is effectively a bound on the number of routers an IP packet may pass through before being discarded. Ping Error Message General Failure Top Of Page Ping Remote Host If the default gateway responds correctly, ping a remote host to ensure that network-to-network communications are operating as expected. Ping Failure Reasons Can a bike computer be used on the rear wheel?

What does the image on the back of the LotR discs represent? http://iipseconline.com/ping-error/ping-error-5555.html What is the possible impact of dirtyc0w a.k.a. "dirty cow" bug? Since it does not know the MAC address during the ARP request in this example, it uses 0000.0000.000 as a placeholder in the broadcast frames sent out of interface Ethernet 0, Internet Delay Experiments. For A Web Page, Html Represents The:

Next, check to make sure that the default gateway address is correct as entered. What's difference between these two sentences? For more information about troubleshooting host name resolution, see "Unable to Reach a Host or NetBIOS Name" earlier in this chapter. check over here Router1#show interface Serial0/0/0 Serial0/0/0 is up, line protocol is up MTU 1500 bytes, BW 1984 Kbit, DLY 20000 usec, reliability 255/255, txload 69/255, rxload 43/255 Encapsulation HDLC, loopback not set Keepalive

Retrieved 8 September 2010. Ping Protocol For troubleshooting purposes, make sure that only one default gateway is configured. ICMP Payload: payload for the different kind of answers; can be an arbitrary length, left to implementation detail.

How common is the usage of yous as a plural of you?

Was the Boeing 747 designed to be supersonic? By definition, a router is built to route packets. Error Message: Request timed out. Different Ping Errors This is not the main goal of a router.

Addison-Wesley. Output the Hebrew alphabet How do I "install" CentOS? Use the Debug Command Before issuing debug commands, please see Important Information on Debug Commands. this content Sending 5, 100-byte ICMP Echos to 12.0.0.1, timeout is 2 seconds: !!!!!

You’ll be auto redirected in 1 second. You can refer to this IANA link for more information regarding types and codes for ICMP. ICMP Type Literal 0 echo-reply 3 destination unreachable code 0 = net unreachable 1 = host unreachable 2 = protocol unreachable 3 = port unreachable 4 = fragmentation needed and DF If the trace doesn't quite reach the destination, it might be because the target host is protected by a firewall.

Router1(config)#access-list 100 permit ip host 12.0.0.1 host 34.0.0.4 Router1(config)#access-list 100 permit ip host 34.0.0.4 host 12.0.0.1 Router1(config)#end Router1#debug ip packet 100 IP packet debugging is on Router1#debug ip icmp ICMP packet Back To The Top Tweet Copyright © 2005-2015 Online Computer Tips.com HOME | ALL TIPS | COMPUTER TUTORIALS | TECH NEWS | RESOURCES | ADVERTISING | ABOUT US | PRIVACY POLICY are the integers modulo 4 a field? ping < Host name of remote host > Run a PathPing analysis to a remote host to verify that the routers on the way to the destination are operating correctly.

Possible ping outputs indicating a problem include the following: H, !N or !P– host, network or protocol unreachable S– source route failed T– return time milli-seconde or 1/4 meters-second (normally in Request Timed Out The ping command timed out because there was no reply from the host. Router1#ping 12.0.0.2 Type escape sequence to abort. e.g on OSX Resolvable host which is up ping -c 1 google.com ; echo $?

The host does not need to completely wake up all devices, and may return to low power mode after a short delay.