Home > Ping Error > Ping Error Msgs

Ping Error Msgs

Contents

To use the PING utility simply open a command prompt from your Start menu or type in cmd from your run command box or your search box. For example type ping 192.168.0.1 to see if the host with the 192.168.0.1 IP address is reachable. Jan 20 17:19:51.843: IP ARP: sent req src 100.0.0.4 0000.0c5d.7a0d, dst 100.0.0.5 0000.0000.0000 Ethernet0. This may result in a severe performance degradation or a network outage. http://iipseconline.com/ping-error/ping-error-65-xp.html

The device (for example, a router or a PC) sends out a sequence of User Datagram Protocol (UDP) datagrams to an invalid port address at the remote host. Sending 5, 100-byte ICMP Echos to 12.0.0.2, timeout is 2 seconds: ..... IETF. In addition, these messages include the first eight bytes of the original message (in this case header of the ICMP echo request, including the quench value), so the ping utility can http://www.onlinecomputertips.com/networking/ping.html

Ping Error Message General Failure

If you are trying to PING something outside of your local network, check if gateway address is correct.

Bad IP address: An invalid IP address was entered on the command prompt Access Blocked Website Even If Domain and IP Are B... To those to whom we have not been able to reply, sorry! The user tries to specify an IP address that is not valid.

The content you requested has been removed. Related Information Using the Extended ping and Extended traceroute Commands Technical Support - Cisco Systems Contributed by Cisco Engineers Was this Document Helpful? Bad IP address address .... For A Web Page, Html Represents The: RAID Interview Questions Interview Questions Section Interview "Trick" Questions Service Desk Team Lead Interview Questions Technical Writer Interview Questions System Administrator Interview Questions Network Administrator Interview Questions Technical Support Interview Questions

How to set up a Trust Relationship between two domains? Ping Messages Explained If you get reply from another device on the way, but not from the host we are troubleshooting, this could also mean there is no route back to your device. Let's say you have an IP mask of 255.255.255.0 (i.e. http://www.itgeared.com/articles/1094-ping-and-icmp-error-messages/ Ping (networking utility) From Wikipedia, the free encyclopedia Jump to: navigation, search An example run of the command-line ping utility on Microsoft Windows Ping is a computer network administration software utility

They are also very easy to use. Ping Protocol Destination net unreachable: The targeted gateway to the IP address written in the command prompt window could not be reached. In this example, the shortest round trip time was 9.674 ms, the average was 10.968 ms, and the maximum value was 11.726 ms. If the local computer's TCP/IP configuration is correct, you can still receive this message from your gateway.

Ping Messages Explained

Retrieved June 26, 2015. ^ "The Story of the PING Program", Mike Muuss ^ Salus, Peter (1994). The command-line options of the ping utility and its output vary between the numerous implementations. Ping Error Message General Failure This may result in a severe performance degradation or a network outage. Ping Failure Reasons Please try again.

If we continuously send such messages using the PING command, the tool will calculate the delay it takes for replies to come back. have a peek at these guys When a ping response is not successful you can get a variety of error replies. Jan 20 16:42:48.895: IP: s=12.0.0.1 (local), d=34.0.0.4 (Serial0), len 28, sending Jan 20 16:42:48.899: UDP src=37534, dst=33441 Jan 20 16:42:51.895: IP: s=12.0.0.1 (local), d=34.0.0.4 (Serial0), len 28, sending Jan 20 16:42:51.899: Yes No Additional feedback? 1500 characters remaining Submit Skip this Thank you! Different Ping Errors

Increase the wait time using the ping -w switch. How to find out the computer name using IP address? Confusingly, you can also get "hardware error" from a configuration error. check over here Bad parameter parameter ....

The TTL value of a ping packet cannot be changed. Ping Output See also[edit] Computer networking portal Keepalive List of DOS commands List of Unix utilities Traceroute Ping of death Ping-pong scheme Security through obscurity Smurf attack References[edit] ^ a b Mike Muuss. If a match cannot be found in an appropriate cache table, the packet is queued in the input queue of the incoming interface to be processed.

This may be used to detect that the remote host was effectively woken up, by repeating a new request after some delay to allow the host to resume its network services.

Host discovery, scanning or ping sweep is a feature of network scanning tools such as nmap, working by utilizing ICMP echo packets. Retrieved 4 June 2010. [text shown if your computer replies to ping requests] "Ping" is among the oldest and most common methods used to locate systems prior to further exploitation. ^ Retrieved 8 September 2010. What Is Ping Routing Issue Interface Down Access-list Command Address Resolution Protocol (ARP) Issue Delay Correct Source Address High Input Queue Drops The Traceroute Command Performance Use the Debug Command Related Information Introduction This

In class B address (ie: 255.255.0.0) the scenario is different. 12:51 AM Post a Comment Newer Post Older Post Home Subscribe to: Post Comments (Atom) Subscriber Count Blog Archive ► 2016 Here are the main error messages and what they mean. Either there was a typo in the hostname, or your name resolution process failed in resolving the IP address for the hostname provided. this content Back To The Top Tweet Copyright © 2005-2015 Online Computer Tips.com HOME | ALL TIPS | COMPUTER TUTORIALS | TECH NEWS | RESOURCES | ADVERTISING | ABOUT US | PRIVACY POLICY

I am trying to present to you the types of reply possible from a destination device, but in fact they are error messages, as a simple reply with no message means Bad value for option value .... We get a better idea of the problem using this debug command: Router4#debug arp ARP packet debugging is on Router4#ping 100.0.0.5 Type escape sequence to abort. Please help us spread the word by socializing it today!

The ping command first sends an echo request packet to an address, then waits for a reply. Jan 20 16:40:22.303: IP: s=20.0.0.1 (local), d=12.0.0.2 (Serial0), len 100, sending. This documentation is archived and is not being maintained. Ping statistics for 4.2.2.2: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\Documents and Settings\vi83>ping 4.2.2.2 Reasons for Getting Ping Hardware Error The possible reasons for getting

U.S. For more information on the PING command, type PING /? When we now try to ping Router4, we have the following: Router1#ping 34.0.0.4 Type escape sequence to abort. There are a couple of ways to minimize the impact of the debug command on the router.

Jan 20 16:16:21.363: IP: s=12.0.0.1 (local), d=34.0.0.4 (Serial0), len 100, sending. ping; transmit failed, error code 10045 solution of the error 3.