Home > Beep Codes > Phoenix Bios Post Error Beep Codes

Phoenix Bios Post Error Beep Codes

Contents

Phoenix BIOS beep codes Below are the beep codes for Phoenix BIOS Q3.07 OR 4.X Beep Code Description and what to check 1-1-1-1 Unconfirmed beep code. Replace the IC if possible 2-2-4 64KB RAM failure Bit 7; This data bit on the first RAM IC has failed. Check RTC and PIT or the system crystal if a failure occurs CPU Return from protected mode. Replace the IC if possible 3-1-1 Slave DMA register failure The DMA controller has failed. Check This Out

Press F1 to start the boot process or F2 to enter Setup and change any settings Real-time clock error Real-time clock fails BIOS test. Replace the IC if possible 2-1-3 64KB RAM failure Bit 2; This data bit on the first RAM IC has failed. Replace the CMOS if possible Low 1-1-3 Extended CMOS RAM failure The extended portion of the CMOS RAM has failed. Might require motherboard repair Shadow RAM failed at offset: nnnn Shadow RAM failed at offset nnnn of the 64KB block at which the error was detected System battery is dead - recommended you read

Phoenix Bios Beep Codes

Replace the IC if possible 3-1-1 Slave DMA register failure The DMA controller has failed. BIOS attempts to locate the address and display it on screen. Replace the CMOS if possible 1-1-4 BIOS ROM checksum error The BIOS ROM has failed. Replace the IC if possible 2-3-2 64KB RAM failure Bit 9; This data bit on the first RAM IC has failed.

Replace the IC if possible 1-3-1 RAM refresh failure The RAM refresh controller has failed 1-3-2 64KB RAM failure The test of the first 64KB RAM has failed to start 1-3-3 All rights reserved. To find out more information on Phoenix beep codes you can go here. Hp Beep Codes Bios Central is a trademark of Bob Hurt.

Replace the IC if possible 2-4-1 64KB RAM failure Bit 12; This data bit on the first RAM IC has failed. Replace the BIOS or upgrade if possible 1-2-1 PIT failure The programmable interrupt timer has failed. Was this page useful? http://www.bioscentral.com/postcodes/phoenixbios.htm Replace the IC if possible 4-3-4 Time of day clock failure The real time clock/CMOS has failed.

Check to see if fixed disk is installed properly. Award Bios Beep Codes Replace the IC if possible 2-1-4 64KB RAM failure Bit 3; This data bit on the first RAM IC has failed. Enter Setup and see if fixed disk and drive A: are properly identified Parity Check 1 Parity error found in the system bus. I verified this with a SIIG (crap -- avoid like the plague) Ultra-66 card, and then confirmed the results with Dell.

Asus Beep Codes

Home· Forums· About Us· Awards· Contact Us· Upgrade your BIOS BIOS UPDATES Click to scan for Bios Updates BIOS PostCodes Acer ALR AMIT/AMI Arche Legacy AST AT&T Award Chips & Technologies http://pcsupport.about.com/od/fixtheproblem/tp/phoenix-beep-codes.htm Replace the IC if possible 1-2-3 DMA read/write failure The DMA controller has failed. Phoenix Bios Beep Codes Replace the IC if possible 2-1-2 64KB RAM failure Bit 1; This data bit on the first RAM IC has failed. Gigabyte Beep Codes Replace the IC if possible 2-3-4 64KB RAM failure Bit 11; This data bit on the first RAM IC has failed.

Logic board problem. his comment is here Replace if possible 1-4-3 EISA fail-safe timer test Replace the motherboard 1-4-4 EISA NMI port 462 test Replace the motherboard 2-1-1 64KB RAM failure Bit 0; This data bit on the Reseat RAM chips or replace RAM chips as possible solution 1-1-1-3 Verify Real Mode. 1-1-2-1 Get CPU Type. 1-1-2-3 Initialize system hardware. 1-1-3-1 Initialize chipset registers with initial POST values. 1-1-3-2 Requires repair of system motherboard Return to Top Phoenix BIOS Post Procedures: CPU Check internal operations i.e. Phoenix Bios Continuous Beep

Replace the IC if possible 2-2-2 64KB RAM failure Bit 5; This data bit on the first RAM IC has failed. Replace the motherboard 4-3-3 Interval timer channel 2 failure The system timer IC has failed. For example, in you insert a Promise Ultra-66 card but do not connect a hard drive to it, you will get the beep code. this contact form All rights reserved.

They use a system of 4 beeps each separated by a small pause i.e. 1 pause 2 pause 1 pause 1 pause (1-2-1-1), you may need to reboot the pc a Phoenix Bios Beep Codes 1-3-4-3 Replace the IC if possible 2-2-3 64KB RAM failure Bit 6; This data bit on the first RAM IC has failed. Reseat the adapter or replace the adapter if possible 4-2-1 Timer failure The system's timer IC has failed.

Replace the IC if possible 1-3-4 First 64KB logic failure The first RAM control logic has failed 1-4-1 Address line failure The address line to the first 64KB RAM has failed

Replace if possible 1-2-2 DMA failure The DMA controller has failed. When a device fails the first part of the POST the BIOS will send a series of beeps from the PC's speaker (internal) to inform the PC user that there is Replace the IC if possible 1-2-3 DMA read/write failure The DMA controller has failed. Intel Beep Codes Problem with SIMM.

High Tone, four higher tones. Replace the IC if possible 4-3-4 Time of day clock failure The real time clock/CMOS has failed. E.g. 1-1-2 would mean 1 beep, a pause, 1 beep, a pause, and 2 beeps. navigate here With a POST board installed, you can monitor the progress of the self-test as it progresses.

Replace the IC if possible 2-2-3 64KB RAM failure Bit 6; This data bit on the first RAM IC has failed. Check to see if fixed disk is installed properly. Beep Code POST Code Failed Test Point / Description 1-1-1-3 02 Verify Real Mode 1-1-2-1 04 Get CPU type 1-1-2-3 06 Initialize system hardware 1-1-3-1 08 Initialize chipset registers with initial Back: Introduction Legal Disclaimer |Copyright Notice© Copyright Totally Hardware 2002-2003 PhoenixBIOS 4.0 Error Beep Codes As the power-on self test progresses, numeric values representing the status of the test are

If possible, replace the MPU Beeps Description 1-1-1-3 Verify real mode 1-1-2-1 Get CPU type 1-1-2-3 Initialize system hardware 1-1-3-1 Initialize chipset registers with initial values 1-1-3-2 Set in POST flag Each 1 in the map indicates a failed bit Fixed Disk 0 Failure Fixed disk is not working or not configured properly. Replace the video adapter if possible 3-4-1 Video initialization failure There is a problem with the video adapter. YesNo Feedback E-mail Share Print Search Recently added pages View all recent updates Useful links About Computer Hope Site Map Forum Contact Us How to Help Top 10 pages Follow us

Replace the IC if possible 2-3-4 64KB RAM failure Bit 11; This data bit on the first RAM IC has failed. Beep Code Description 1 long, 2 short Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information 1 long, 3 short Video Submitted by John Palmer. The error message will be either a numeric code or a text message.

Run Setup to be sure the fixed disk type is correctly identified Fixed Disk Controller Failure Fixed disk is not working or not configured properly. Replace the IC if possible 2-1-4 64KB RAM failure Bit 3; This data bit on the first RAM IC has failed. As any experienced technician knows, a failure at any given location does not necessarily mean that the particular part or section under test has actually failed. Replace the IC if possible 2-2-1 64KB RAM failure Bit 4; This data bit on the first RAM IC has failed.

Replace the CMOS if possible 1-1-4 BIOS ROM checksum error The BIOS ROM has failed.