Home > Beep Codes > Phoenix Bios Error Signals

Phoenix Bios Error Signals

Contents

Replace the CMOS if possible 4-4-1 Serial port failure A error has occurred in the serial port circuitry 4-4-2 Parallel port failure A error has occurred in the parallel port circuitry Replace the CMOS if possible Low 1-1-3 Extended CMOS RAM failure The extended portion of the CMOS RAM has failed. Replace the video adapter if possible 3-4-1 Video initialization failure There is a problem with the video adapter. Replace the IC if possible 1-2-3 DMA read/write failure The DMA controller has failed. Check This Out

Replace the IC if possible 3-3-1 CMOS RAM power bad Replace the CMOS battery or CMOS RAM if possible 3-3-2 CMOS configuration error The CMOS configuration has failed. Continue Reading Up Next Up Next Article CMOS & CMOS Batteries: Everything You Need to Know Up Next Article What Does it Mean to 'Boot' a Computer? Replace the IC if possible 2-1-3 64KB RAM failure Bit 2; This data bit on the first RAM IC has failed. Article What is a POST Error Message? http://www.bioscentral.com/beepcodes/phoenixbeep.htm

Phoenix Bios Beep Codes

Replace the CMOS if possible 4-4-1 Serial port failure A error has occurred in the serial port circuitry 4-4-2 Parallel port failure A error has occurred in the parallel port circuitry Replace the motherboard 1-1-3 CMOS read/write error The real time clock/CMOS is faulty. Replace the IC if possible 4-3-4 Time of day clock failure The real time clock/CMOS has failed.

BIOS attempts to locate the address and display it on screen. All rights reserved. Replace the controller if possible 3-1-2 Master DMA register failure The DMA controller had failed. Hp Bios Beep Codes However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary.

Replace the IC if possible 2-1-2 64KB RAM failure Bit 1; This data bit on the first RAM IC has failed. Phoenix Bios Continuous Beep However, if the computer fails the POST, the computer will either not beep or generate a beep code that tells the user the source of the problem. Reseat the adapter or replace the adapter if possible 4-2-1 Timer failure The system's timer IC has failed. Replace the IC if possible 2-4-4 64KB RAM failure Bit 15; This data bit on the first RAM IC has failed.

I verified this with a SIIG (crap -- avoid like the plague) Ultra-66 card, and then confirmed the results with Dell. Phoenix Bios Beep Codes 1-3-4-3 Press F1 to start the boot process or F2 to enter Setup and change any settings Real-time clock error Real-time clock fails BIOS test. The error message will be either a numeric code or a text message. Replace the IC if possible 2-1-4 64KB RAM failure Bit 3; This data bit on the first RAM IC has failed.

Phoenix Bios Continuous Beep

When a device fails the first part of the POST the BIOS will send a series of beeps from the PC's speaker (internal) to inform the PC user that there is Replacing the RAM is the usual recommendation for solving this problem. 1-4-1-1 Beep Code Pattern Thomas Vogel/E+/Getty Images A 1-4-1-1 beep code pattern on a PhoenixBIOS system means that there is Phoenix Bios Beep Codes Replace if possible 1-2-2 DMA failure The DMA controller has failed. Asus Beep Codes Replace the BIOS or upgrade if possible 1-2-1 PIT failure The programmable interrupt timer has failed.

Replace the IC if possible 2-1-2 64KB RAM failure Bit 1; This data bit on the first RAM IC has failed. his comment is here BIOS attempts to locate the address and display it on screen. Bios Central is a trademark of Bob Hurt. unused This document contributed to the Computer Technology Documentation Project by: Table of Contents Introduction AMI & Award BIOS beep codes IBM & Macintosh BIOS beep codes Phoenix BIOS beep codes Gigabyte Beep Codes

Replace the IC if possible 3-3-1 CMOS RAM power bad Replace the CMOS battery or CMOS RAM if possible 3-3-2 CMOS configuration error The CMOS configuration has failed. For example, in you insert a Promise Ultra-66 card but do not connect a hard drive to it, you will get the beep code. Replace the IC if possible 2-2-2 64KB RAM failure Bit 5; This data bit on the first RAM IC has failed. this contact form Please try again.

E.g. 1-1-2 would mean 1 beep, a pause, 1 beep, a pause, and 2 beeps. Test 51k Base Memory Error This Could Be What You're Missing More From Us Article Is Your Computer Making Beeping Noises? Powers on, no tone.

Replace the IC if possible 1-2-3 DMA read/write failure The DMA controller has failed.

Replace the motherboard 4-3-3 Interval timer channel 2 failure The system timer IC has failed. Replace the BIOS or upgrade if possible 1-2-1 PIT failure The programmable interrupt timer has failed. Most often, it's a problem with the system memory. Award Bios Beep Codes Article Everything You Need to Know About the PC POST Process Article Can't Access BIOS?

Replace the IC if possible 2-2-3 64KB RAM failure Bit 6; This data bit on the first RAM IC has failed. Logic board problem. If true, default BIOS values set on next POST 0C Initialize I/O module control registers 0E External CPU caches initialized; Cache registers set to default values 10/12/14 Verify response from 8742 http://iipseconline.com/beep-codes/phoenix-bios-error-beep.html Replace the video adapter if possible 3-4-1 Video initialization failure There is a problem with the video adapter.

E.g. 1-1-2 would mean 1 beep, a pause, 1 beep, a pause, and 2 beeps. With a Dell computer, a 1-2 beep code can also indicate that a bootable add-in card is installed but no boot device is attached. Other Phoenix Beep Codes Many other PhoenixBIOS beep codes exist but are very uncommon. advertisement The POST test is a two stage process, first it will check all of the basic components including amongst other things, the system clock, the processor, RAM, the keyboard controller

Beep Code Description No Beeps No Power, Loose Card, or Short. 1 Short Beep Normal POST, computer is ok. 2 Short Beep POST error, review screen for error code. After the video has been tested successfully the BIOS will then display any errors encountered on the screen. Replace the CMOS if possible Low 1-1-3 Extended CMOS RAM failure The extended portion of the CMOS RAM has failed. Replace the IC if possible 2-4-1 64KB RAM failure Bit 12; This data bit on the first RAM IC has failed.

Find us on Google+ System Specific Diagnostic and POST Error Messages: IBM Diagnostic Error Codes Compaq Desktop Systems Diagnostic and POST Errors BIOS Related Pages: BIOS Data Area BiosCentral Forums BIOS Replace the motherboard 1-1-3 CMOS read/write error The real time clock/CMOS is faulty. Replacing the RAM usually fixes this problem. 2-1-2-3 Beep Code Pattern A 2-1-2-3 beep code pattern means that there has been a BIOS ROM error, meaning an issue with the BIOS Replace the IC if possible 3-1-1 Slave DMA register failure The DMA controller has failed.